LightMaster Dimmer Actuator
PDLPC 416FR-KNX

This Dimmer Actuator is designed to provide cost-effective control of DALI high frequency fluorescent ballasts.Each of the four control outputs support DALI broadcast ,DALI Addressed, 1-10V and DSI protocols. The control signals can be programmed to operate in tandem with the four internal switched outputs, which will automatically isolate the power circuit when all associated channels are at 0%. This feature is useful for energy savings applications,as DALI ballasts draw a significant amout of power when the lamps are turned off via a DALI command. The device is DIN rail mountable, designed to be installed in a switchboard next to the circuit breakers supplying power to the controlled lighting circuits.The device contains an integral DALI bus power supply, removing the need for an additional power supply external device.

LightMaster DALI Multi Master Actuator
PDBC120-DALI-KNX

The DALI Multi Master Actuator is designed for cost-effective control of DALI compatible lamp drivers, providing a full universe of 64 DALI channels & communication to Philips Controls, DALI user interfaces including multifunction sensor and dry contact interface.Direct DALI to KNX mapping means that the DALI-imposed limits, such as the maximum of 16 groups, are seamlessly overcome allowing for a fully scalable network solution. Thisdevice is DIN rail mountable, designed to be installed in a switchboard that is supplying power to the controlled lighting circuits. The device contains an integral DALI bus power supply, removing the need for the provision of a separate external supply which reduces switchboard wiring complexities.

LightMaster Structured Cabling Dimmer Actuator
PLPC905GL-3-KNX,PLPC905GL-3-HD-KNX&PLPC905GL-4-KNX,PLPC905GL-4-HD-KNX

This range of devices are high frequency fluorescent dimmer actuators designed for direct installation within ceiling cavities with power and communications connections via a structured cabling solution,Rach control output supports DALI broadcast ,DALI addressed,1-10V and DSI protocols. For ease of installation and maintenance the device incorporatesstructured wiring connectors, which enables the unit to be readily connected without the use of tools. The device can be readily integrated with a Building Management System(BMS) via the knx control network,making it ideally suited tio commercial office installations wher a cost-effective control solution is required. The device design provides easy connectionwithout the use of tools and is available for 3 or 4 pole Wieland power wiring and 2 polecommunication wiring systems. It is also available with optional HD – Heavy Duty relays forapplications where high inrush currents occur.

LightMaster Relay Actuators
PDRC416FR-KNX,PDRC816FR-KNX&PDRC1216FR-KNX

These relay actuators are designed to control any type of switched load and are available in4,8&12 pole configuration.The power circuit is of a’feed through’ design and is electrically equivalent to a 4, 8 or 12 pole contactor, with the additional advantage of each pole being separately controllable via the KNX network. The relay actuators are DIN rail mountable, designed to be installed in a switchboard next to the circuit breakers feeding the circuits to be controlled.Each channel is fitted with a hardware override switch which is accessible from the front panel. The LightMaster relay actuator range generally does not require an additional power supply unless synchronous switching of several channels is necessary.

The LightMaster Line Coupler
PLC-KNX

The Philips PLC-KNX is designed for cost-effective optical isolation of KNX networks. The two opto-isolated KNX ports enable the PLC-KNX to implement a main line and line topology, with each line being electrically isolated from the others so a fault in one section of the network will be contained.it is a 'passive' device that does not require programming.

LightMaster Network Power Supply
PPS640-KNX

The PPS640-KNX is a regulated power supply with an integrated Bus choke, designed to provide network DC supply to the KNX network. The switchmode design allows the device to be used with a wide range of supply voltages without the need for a manual selector setting. The PPS640-KNX is housed in a 6 unit dinrail mount enclosure that has a circuit breaker paofile.This enables the device to be installed in all types of electrical equipment enclosures, including those with vover apertures specifically designed for circuit breakers.

LightMaster Multifunction Sensor
PLOS-CM-KNX&PLOS-CM-DALI

The PLOS-CM-KNX&PLOS-CM-DALI are low profile recessed flush mount 360 ceiling mount sensors that combine motion detection – PIR and ambient light level detection(PE)-in the one device. in applications such as office buildings these universal sensors can be utilised to detect motion and switch on the lights or aprogrammed lighting scene. When rooms are unoccupied, lights can be automaticallydimmed or switched off to provide energy savings. These units also incorporate a segmented click-up bezel surrounding the motion sensor element. This enables a portiom of the sensing filed to be readily masked to prevrent nuisance detecuion from adjacent doorways or corridors. In situations where it is critical to precise lighting control for individual workspaces,such as an office workstation,the sensors facilitate light compensation. The PLOS-CM-KNX is powered directly by theKNX network. The PLOS-CM-DALI is powered directly by the DALI network that is running brtween the DALIlight fittings thus eliminating the need for additional network field wining.THE    PLOS-CM-DALI sensor can only be used when connected with a Philips KNX MultiMaster controller such as the PDBC120-DALI-KNX unit.

Dry Contact Interfaces
PIPS-KNX-2P & PIPE-KNX-4P

The PPMI940-DALI is a four-channel input dry contact interface, designed to allow mechanical and electronic switches to interface directly with a DALI network and the Philips KNX MultiMaster controller such as the PDBC120-DALI-KNX unit.The PPMI4-KNX is a four way dry contact interface designed to allow mechanical switches and relays to interface to the KNX network. In addition these devices canbe used as a simple dry contact interface for low level integration to third-party systems such as security and air conditioning so that the lighting can be coordinatedtogether with other services found within a project. The function of each input is programmable and the small size of the product makes it perfect for installation behind multi-gang switch grids.

LightMaster Switch Panel Range
PIPE-KNX-2P & PIPE-KNX-4P

Contemporary design and smart operation are just two factors integrated into the lighmaster PIPE-KNX-2P & PIPE-KNX-4P switch panel range.with a very flexble base module component,both specifiers and installers get more functionality to control complex functions in all types of commercial buildings. Straight switching as well asmultifunction combinations including dimming, blind and scene control can all be achieved. All of these factors add up to provide maximum comfort for users as wellas minimum energy management possibilities for building operators and owners. Available in 2 position and 4 position options with engraving opportunites availableon a project basis.